The "Classic" solenoid operators sturdy and tough construction with a 1/2" NPT conduit connection. The stem exhaust is tapped 10-32. Voltage must be specified when ordering valves that use this operator. If no voltage is specified, then 120/60 is provided. Other voltages not shown below are available. Coil can be rotated in any direction on operator stem when space is available. Caution must be used when rotating coil so not to untighten the stem from the adaptor block. Standard leads are 18", longer leads available on request. When connecting to an electrical source either black wire can be connected to hot (+) and the other connected to neutral (-).

Voltage	Pick-Up	Holding	Resistance	Operator	Spare Coil*
24 volts, 60 Hz	1.72 amps	1.10 amps	5.39 ohms	AY-38-4	V-67-4
120 volts, 60 Hz	0.36 amps	0.23 amps	135 ohms	AY-38-11	V-67-11
240 volts, 60 Hz	0.18 amps	0.12 amps	546 ohms	AY-38-17	V-67-17
12 volts D-C		1.20 amps	12.8 ohms	AY-38-5	V-67-5
24 volts D-C		0.58 amps	61 ohms	AY-38-8	V-67-8

The "Classic" solenoid operators sturdy and tough construction with a 1/2" NPT conduit connection. The stem exhaust is tapped 1/8" NPTF. Voltage must be specified when ordering valves that use this operator. If no voltage is specified, then 120/60 is provided. Other voltages not shown below are available. Coil can be rotated in any direction on operator stem when space is available. Caution must be used when rotating coil so not to untighten the stem from the adaptor block. Standard leads are 18", longer leads available on request. When connecting to an electrical source either black wire can be connected to hot (+) and the other connected to neutral (-).

Voltage	Pick-Up	Holding	Resistance	Operator	Spare Coil*
24 volts, 60 Hz	1.72 amps	1.10 amps	5.39 ohms	AY-38T-4	V-67-4
120 volts, 60 Hz	0.36 amps	0.23 amps	135 ohms	AY-38T-11	V-67-11
240 volts, 60 Hz	0.18 amps	0.12 amps	546 ohms	AY-38T-17	V-67-17
12 volts D-C		1.20 amps	12.8 ohms	AY-38T-5	V-67-5
24 volts D-C		0.58 amps	61 ohms	AY-38T-8	V-67-8

The "Classic" DIN solenoid operator with a ISO 4400 din pattern connection (Form A, DIN 43650-A, 18 mm contact distance). DIN caps are ordered as a separate line item. The stem exhaust is tapped 10-32. Voltage must be specified when ordering valves that use this operator. If no voltage is specified, then 120/60 is provided. Other voltages not shown below are available. Coil can be rotated in any direction on operator stem when space is available. Caution must be used when rotating coil so not to untighten the stem from the adaptor block. An approved cap must be used when connecting to an electrical source. The longer tab is the ground (earth). Either shorter tab can be connected to hot (+) and the other connected to neutral (-).

Voltage	Pick-Up	Holding	Resistance	Operator	Spare Coil*
120 volts, 60 Hz	0.36 amps	0.23 amps	135 ohms	AY-38ED-11	V-67ED-11
240 volts, 60 Hz	0.18 amps	0.12 amps	546 ohms	AY-38ED-17	V-67ED-17
12 volts D-C		1.20 amps	12.8 ohms	AY-38ED-5	V-67ED-5
24 volts D-C		0.58 amps	61 ohms	AY-38ED-8	V-67ED-8

The "Classic" explosion proof solenoid operators are sturdy and tough construction with a 1/2" NPT conduit connection. The stem exhaust is tapped 1/8"-27 NPT. Voltage must be specified when ordering valves that use this operator. If no voltage is specified, then 120/60 is provided. Other voltages not shown below are available. Coil can be rotated in any direction on operator stem when space is available. Caution must be used when rotating coil so not to untighten the stem from the adaptor block. The explosion proof operator carries the UL & CSA label for Class I, Division 1, Group C and D (gasoline vapors, etc.), Class II, Division 1, Groups E, F and G (coal , coke and grain dusts). Temperature code: T4A. Standard leads are 18". When connecting to an electrical source either black wire can be connected to hot (+) and the other connected to neutral (-). The green wire is the ground (earth). The housing of all "Classic" explosion proof solenoids cannot be rotated or serviced in the field. If coil orientation is not specified at time of order, the 1/2" conduit will be rotated towards the 2 port side of valve body.

Voltage	Pick-Up	Holding	Resistance
24 volts, 60 Hz	1.72 amps	1.10 amps	5.39 ohms
120 volts, 60 Hz	0.36 amps	0.23 amps	135 ohms
240 volts, 60 Hz	0.18 amps	0.12 amps	546 ohms
12 volts D-C		1.20 amps	12.8 ohms
24 volts D-C		0.58 amps	61 ohms

The "Classic" Mold-Over solenoid operator with a 1/2"-14 NPT conduit connection. The stem exhaust is tapped 10-32. Voltage must be specified when ordering valves that use this operator. If no voltage is specified, then 120/60 is provided. Other voltages not shown below are available. Coil can be rotated in any direction on operator stem when space is available. Caution must be used when rotating coil so not to untighten the stem from the adaptor block. Standard leads are 18", longer leads available on request. When connecting to an electrical source either black wire can be connected to hot (+) and the other connected to neutral (-). The green wire is the ground (earth).

Voltage	Pick-Up	Holding	Resistance	Operator	Spare Coil*
120 volts, 60 Hz	0.36 amps	0.23 amps	135 ohms	AY-38M-11	V-67M-11
240 volts, 60 Hz	0.18 amps	0.12 amps	546 ohms	AY-38M-17	V-67M-17
12 volts D-C		1.20 amps	12.8 ohms	AY-38M-5	V-67M-5
24 volts D-C		0.58 amps	61 ohms	AY-38M-8	V-67M-8