ESY8PGALZ Valve Data - AAA Products International

AAA Products International Inc.
7114 Harry Hines Blvd.
Dallas, Texas 75235
214-357-3851

Data for ESY8PGALZ

The ESY8PGALZ 24VDC is a 1" NPTF subplate style, 3 position, spring centered, float (open) center spool, double solenoid operated valve with externally pressurized solenoid valve and a dust excluder nut on the solenoid stem. The spool is shifted by 50 to 115 psi external pilot air when the solenoid is energized. 50 to 115 psi must be maintained to the solenoid to keep the spool shifted while the coil is energized. The spool is spring centered when both solenoids are de-energized. Valve must be used with a subplate style connection. See the dedicated subplate section. See additional information on solenoid valve operation. Coil and operator are only available in 24VDC intrinsically safe and must be used with a compatible barrier.

Details

Pressure: 15 to 250 psi on the main body of the valve when solenoid is externally piloted.
Vacuum: The five main ports can be operated on industrial vacuum to 28" Hg, based on a 30" barometer.
Temperature: -20°F to 120°F ambient. Caution: If it is possible that the ambient temperature may fall below freezing, the medium must be moisture free to prevent internal damage or unpredictable behavior.
Mounting: The valve can be mounted in any orientation.
O-Rings: Buna-N.
Solenoid Seat: Viton.
Materials: Black anodized 356-T6 aluminum body, hard anodized aluminum spool, A380 aluminum end caps, Viton solenoid seat, composite gaskets, steel fasteners.
Flow: 478 SCFM, 11.1 Cv
Repair Kit: ERKV-8.
3-Way or 5-Way: This valve is basically 4-way, it must be configured for external pilot (Option 'Z') for 5-way service by using ports 2 or 4 as an inlet, or 3-way service by plugging the unused port 2 or 4.
Fluid Media: Soft seal models are made for air, vacuum, and gases compatible with component materials. They should not be used with liquids.

"E-Series" Coil - Option A - Intrinsically Safe

When related to solenoid valves, intrinsic safety means that the coil's current draw and resulting temperature is held to such a low level (when used with an approved safety barrier) that the valve no longer has the capability of igniting a mixture of flammable or combustible material, either during normal operation or under fault conditions. Typically, they are used in situations where fire and explosive hazards exist due to the presence of flammable gases, vapors or liquids, combustible dusts or easily ignitable fibers. Intrinsically safe coils and operators are sold as a matched set and must be ordered as V-564 (individual components are not available). Solenoid operator maximum pressure is 115 psi.
These operators are equipped with the standard V-562 nut but can be ordered with a V-567W bronze muffler nut (option L) or a V-562 side exhaust nut (option C).
These 24 VDC coils are approved according to EN 50 020 respectively DIN VDE 0170/0171 part 5 for hazardous location. Class I, groups A, B, C and D; Class II, groups E, F and G; Class III. This coil is an ISO 4400 DIN style pin pattern. A non-indicator, cord grip style cap is provided. A copy of the certification is available here. An approved cap (included) must be used when connecting to an electrical source. The longer tab is the ground (earth). Either shorter tab can be connected to hot (+) and the other connected to neutral (-).

Material: Brass, steel, stainless steel, Viton seat.
Molding Material: Thermoset resin.
Ambient Temperature: -20°C to +50°C.
Internal Diameter Orifice: 0.8mm
Relative Duty Cycle: 100%.
Degree of Protection: IP65 with connector.
Certifications: This coil carries the following certificate of compliance. The rating only applies to the coil/operator and not the entire valve.
Insulation Class: F
Electrical Characteristics: 21.6 - 28 VDC

"E-Series" Intrinsically Safe Barrier

The proper use of the intrinsically safe solenoid operator requires the use of a barrier in the non-hazardous location with the solenoid operator in the hazardous location. We do not recommend nor endorse any barrier manufacturer or product but include a list to start your research. It is up to the user to verify barrier information. (Company and contact information may change.)
Barrier Schematic

COMPATIBLE BARRIER MANUFACTURERS

Pepperl & Fuchs Inc. - Telephone (330) 425-3555 - FAX: (330) 425-4607
Pepperl+Fuchs, Inc., 1600 Enterprise Parkway, Twinsburg, Ohio 44087
E-mail: sales@us.pepperl-fuchs.com - www.pepperl-fuchs.com
Models: KFD2-SLS-EX2 and KFD2-SD-EX1.36

Eaton
Process Safety Automation Measurement
www.eaton.com/us/en-us/products/process-safety-automation-measurement/intrinsic-safety
Model: MTL5525

STAHL, INC - Telephone: (800) 782-4357
R. Stahl, Inc.
13259 N. Promenade Blvd, Stafford, TX 77477
E-Mail: sales.us@r-stahl.com - www.rstahl.com
Model: 9275/10-24-48-11s

"E-Series" Nut - Dust Excluder

Sintered bronze dust excluder nut, part number V-567W reduces the noise and diffuses the solenoid exhaust. The nut comes with a V-613 lock washer to improve nut retention. With this option the 10-32/5mm-0.8 tapped exhaust is inaccessible. To order standard solenoid valves with this nut, use option 'L' (e.g. ESY4L).

Subplates for 8P Valves - 3/4" Ports

Subplated valves require a mounting base. This mounting base is pre-plumbed to existing control lines. Due to the nature of the plumbing lines fixed to a mounting base, replacing subplate mounted valves is rapid and quick. All port connections, excluding "External Pilot" or "Pilot Return" ports, if used, are made through O-ring sealed holes in the base of the valve through a subplate. O-ring seals and mounting screws are furnished with each subplate valve.

The typical sublates are listed below from the most commonly used to the least commonly used.

Part Number	Description	Image
SP6-3N	3/4" Side ported, dual exhaust, no pilot ports.
SP6-1N	3/4" Bottom ported, dual exhaust, no pilot ports.
SP6-4N	3/4" Side ported, single exhaust, no pilot ports.
SP6-2N	3/4" Bottom ported, single exhaust, no pilot ports.

Subplates for 8P Valves - 1" Ports

The typical sublates are listed below from the most commonly used to the least commonly used.

Part Number	Description	Image
SP8-3N	1" Side ported, dual exhaust, no pilot ports.
SP8-1N	1" Bottom ported, dual exhaust, no pilot ports.
SP8-4N	1" Side ported, single exhaust, no pilot ports.
SP8-2N	1" Bottom ported, single exhaust, no pilot ports.

General - Installation & Maintenance

Valves should be installed with reasonable accessibility for service. Exercise care in keeping tubing lengths to a minimum. Plumbing should be free of contamination. Pipe joint compound should be used sparingly applied only to the thread, never the valve body. Over tightening of pipe threads can fracture the joint causing leaks or failure. Protect the valve from exposure to extreme temperatures, dirt and moisture to maximize life.
Bulletin A-113: Operating & Maintenance Instructions.
Installation: Valve Fitting Installation.

WARNING:These products can expose you to chemicals which is(are) known to the State of California to cause cancer or reproductive harm. For more information, go to www.P65Warnings.ca.gov. Contact us for specific chemicals or materials used in a product.

General - Lubrication, Standard

All valves are pre-lubricated at the factory using Magnalube-G Teflon based all purpose grease. Valves are suitable for, and perform best in a non-lube service. For long life, use an air line filter/lubricator installed no further than 10-ft. from the valve. The filter should be rated 25 pm or finer. Use a good grade of petroleum base lubricating oil no heavier than SAE 10W. DO NOT OVER-LUBRICATE. This could cause the spool to stick. CAUTION! Do not use questionable fluids in air line lubricators. Do not use petroleum oil with detergent additives. Detergents, volatile or aromatic fluids may swell rubber seals in valves and cylinders. Never use cooking or vegetable oil as a lubricant. When cleaning AAA valves after extended service, lubricate the valve spool with AAA high film strength grease, or, use O-ring grease which is usually available from supply houses which sell O-rings. Magnalube-G is included in all valve repair kits for proper valve maintenance. If an additional amount of Magnalube-G grease is required, a 0.75 ounce tube is available under part number VGK-3. Never use any kind of oil, cup grease, or automobile chassis lubricant.

The shelf life of Magnalube-G regularly lasts for 10+ year intervals in closed packaging due to the extremely long operating life of the Elastomer-PTFE gelling agent and premium parafiinic mineral base oil. If the valve is stored for over 2 years, then a small reapplication of grease is suggested.

Magnalube-G Technical Document
Magnalube-G MSDS Document

An alternative grease for low temperature application, refer to Dow-55 grease.

General - O-Ring Information

Unless otherwise specified, all 1/4" and 3/8" soft seal valves come standard with Viton O-rings and all 1/2", 3/4", 1", 1-1/2" and 2" soft seal valves come standard with Buna-N O-rings. If a different material is required, use the dash numbers following the basic valve numbering code. For example, model RY3G-2 will have Silicone O-rings installed for a low temperature application. On valves larger than 1" consult factory on availability of O-ring materials. Additional O-ring material information.

Dash No.	O-ring Description	Temperature Rating
-2	Silicone	-80°F to 400°F
-3	Viton for most aromatic gases	-20°F to 400°F, 600°F for short time
-7	Urethane, 70 Durometer	-65°F to 200°F
-9	Buna-N	-40°F to 250°F

We are constantly researching O-ring materials to evaluate performance and durability in the AAA valve product line. Above is a compilation of the most commonly requested O-ring materials and the associated dash number. If you have a particular application that requires an O-ring material that is not listed, please contact us. Since we utilize standard O-ring dimensions in our valves, we can respond to the most obscure O-ring material request.